Health & Safety

COSHH for builders: silica dust and hazardous substances

12 min read

The short answer

The Control of Substances Hazardous to Health Regulations 2002 (COSHH) require an employer to assess the risk from any hazardous substance its work creates, then prevent exposure or, where that is not reasonably practicable, control it adequately. On a building site the main substance is dust, and the most dangerous is respirable crystalline silica from cutting, chasing and drilling concrete, blocks, brick, mortar and stone. Its workplace exposure limit in HSE’s EH40 is 0.1 mg/m³ averaged over 8 hours, and as a carcinogen it must be kept as low as is reasonably practicable. HSE expects water suppression or on-tool extraction with an H or M class unit, usually with RPE of assigned protection factor 20, face-fit tested for tight-fitting masks. Extraction is thoroughly examined at least every 14 months, and regularly exposed workers may need health surveillance.

At a glance

Regulations
COSHH 2002, S.I. 2002/2677
Silica limit (EH40)
0.1 mg/m³ respirable, 8-hour average
Hardwood dust limit
3 mg/m³ inhalable, 8-hour average
Written assessment
5 or more employees (reg 6(4))
Dust extraction class
H or M (HSE CIS36)
Construction RPE
APF 20, face-fit tested if tight-fitting
Extraction examined
At least every 14 months (reg 9(2))
Health records kept
At least 40 years (reg 11(3))

What does COSHH require of a builder?

A substance hazardous to health includes anything classified as a health hazard, anything with a workplace exposure limit (WEL), and any dust at all once it reaches 10 mg/m³ inhalable or 4 mg/m³ respirable over 8 hours. The duties run in order:

  • Assess (regulation 6). A suitable and sufficient assessment before the work starts, covering the substance, the supplier’s safety data sheet, the level and duration of exposure, the WEL and the controls. With five or more employees, the significant findings are written down.
  • Prevent or adequately control (regulation 7). Substitute first. Otherwise control at source, with PPE only where nothing else achieves adequate control, applying the eight principles of good practice in Schedule 2A.
  • Use and maintain the controls (regulations 8 and 9). Make sure they are used, keep them in good repair, and have extraction thoroughly examined and tested.
  • Monitor exposure (regulation 10) where the assessment shows it is needed to keep control adequate or protect health.
  • Health surveillance (regulation 11) where an identifiable disease is reasonably likely and there is a valid way to detect it.
  • Inform, instruct and train (regulation 12): the substances, the risks, the WEL, access to the data sheet, the findings and what each person must do.

A self-employed person working on a construction site carries the same duties for their own work, except monitoring and health surveillance. An employer’s duties also extend, so far as reasonably practicable, to anyone else affected: the householder, the other trades, the neighbour.

NoteAsbestos and lead sit outside COSHH, under the Control of Asbestos Regulations 2012 and the Control of Lead at Work Regulations 2002. For asbestos, start with the right survey before work starts. Northern Ireland has its own COSHH Regulations of 2003.

Why is silica dust the main risk on site?

Silica is in most rock, sand and clay, and so in concrete, blocks, bricks, tiles and mortar. HSE puts sandstone at more than 70% silica and granite at 15 to 30%. Cutting, drilling, chasing or grinding these materials makes dust, and the finest fraction, respirable crystalline silica (RCS), is invisible in normal light and reaches deep into the lungs.

HSE links RCS to lung cancer, silicosis and chronic obstructive pulmonary disease, and says estimates it commissioned put silica behind the deaths of over 500 construction workers in 2005. Silicosis is irreversible and can keep worsening after exposure stops.

The GB workplace exposure limit for respirable crystalline silica is 0.1 mg/m³ as an 8-hour time-weighted average, and EH40 marks it as a carcinogen where a work process generates it. Under the limit is the minimum; as low as reasonably practicable is the duty.

What are the exposure limits for construction dusts?

DustWEL, 8-hour averageEH40 notes
Respirable crystalline silica0.1 mg/m³ respirableCarcinogen where generated by a work process
Hardwood dust3 mg/m³ inhalableCarcinogen, sensitiser; applies to the whole mix if mixed with other wood dust
Softwood dust5 mg/m³ inhalableSensitiser
Portland cement10 mg/m³ inhalable, 4 mg/m³ respirable
Gypsum (plaster)10 mg/m³ inhalable, 4 mg/m³ respirable
Any other dust10 mg/m³ inhalable, 4 mg/m³ respirableThe level at which COSHH applies to it

From EH40/2005 (fourth edition, 2020), the current list of GB workplace exposure limits.

A WEL is a concentration in the air the worker breathes, averaged over a shift. It is checked by personal air monitoring, not by eye. HSE’s point for builders is simpler: high-energy tools such as cut-off saws and grinders make a lot of dust very quickly, so the controls go on before the cut.

How do you control dust on site?

HSE’s construction dust guidance (CIS36) follows the same order as regulation 7.

  1. 01Stop or reduce the dust. Order materials to size, have them cut off site, use a block splitter instead of a cut-off saw, or a direct fastening system instead of drilling.
  2. 02Water suppression. Enough water at the right rate for the whole time the work is being done. HSE says wetting the material beforehand does not work.
  3. 03On-tool extraction. A captor hood on the tool connected to an H (high) or M (medium) class extraction unit, not a general commercial vacuum. HSE says an L (low) class unit suits only lower-toxicity dust such as gypsum from plasterboard.
  4. 04RPE as well, in most cases. HSE’s general level for construction dust is an assigned protection factor (APF) of 20, meaning the wearer breathes a twentieth of the dust in the air: an FFP3 disposable mask, a half mask with a P3 filter, or a powered hood (TH2) for longer work. RPE is the last line, and relying on it alone has to be justified.
  5. 05Other controls. Keep people away, sheet or screen the area, rotate the work, and clean with a vacuum rather than a brush.
TaskControl HSE gives
Cutting blocks, kerbs and paving with a cut-off sawWater suppression and RPE of APF 20
Chasing concrete and raking mortarOn-tool extraction to an H or M class unit and RPE of APF 20; consider powered RPE for long work
Drilling as a main activityOn-tool extraction to an H or M class unit and RPE of APF 20
Cutting or sanding wood with power toolsOn-tool extraction to an H or M class unit and RPE of APF 20
Sanding plasterboard jointingOn-tool extraction to an H, M or L class unit

Selected rows from Table 1 of HSE CIS36, Construction dust.

Keeping the controls working

Regulation 9 requires local exhaust ventilation, which includes on-tool extraction, to be thoroughly examined and tested at least every 14 months, and reusable RPE to be examined at suitable intervals. Records of those examinations and any repairs are kept for at least five years. HSE’s on-tool extraction guidance (CIS69) adds a formal check at least weekly: the hood and hose for damage, the airflow indicator, and the filters. If the extractor is hired, ask the hire company for its test record.

What does face-fit testing involve?

A tight-fitting mask only protects if it seals to the wearer’s face, and faces differ. HSE’s guidance on fit testing (INDG479) says the COSHH Approved Code of Practice requires tight-fitting RPE to be fit tested as part of selecting it.

  • Test each wearer with the specific make, model and size they will use.
  • Repeat the test when the model, size or material changes, or the wearer’s face does: weight change, substantial dental work, scars or piercings near the seal, or new head-worn PPE.
  • Use a competent tester. Accreditation under the Fit2Fit scheme, which HSE supports, is one way to show competence.
  • Keep the report, stating pass or fail, where the wearer and an inspector can see it. The employer pays for the test.
  • Wearers must be clean-shaven where the mask seals, every time they wear it. Hair between the skin and the seal, stubble included, stops it sealing.
  • A pre-use seal check each time the mask goes on does not replace the fit test.

NoteLoose-fitting powered hoods and helmets do not need fit testing, so they suit an operative with a beard or one who fails the test with every mask tried.

When is health surveillance needed for silica?

Regulation 11 requires health surveillance where an identifiable disease may be related to the exposure, is reasonably likely in the conditions of the work, and can be detected by a valid, low-risk technique. HSE’s guidance on silica (G404) applies that to construction:

  • It must be considered for workers in high-risk occupations, which include construction when cutting or breaking stone, concrete or brick.
  • It must be provided where workers are regularly exposed to RCS and there is a reasonable likelihood that silicosis may develop. Relying on RPE as a control is one of HSE’s signs that it may be needed.
  • A competent occupational health professional runs it: a baseline before exposure, or within about six weeks of starting, then a questionnaire, lung function testing and chest X-rays at the frequency they advise.
  • Each worker’s health record holds their name, address, National Insurance number, the processes they work on, when exposure started and how often, the PPE used and the results. It is kept for at least 40 years.

Cement needs surveillance of a different kind. HSE recommends skin checks for dermatitis by a trained responsible person, starting before or soon after a new worker begins. Diagnosed occupational dermatitis and asthma can be reportable: see what a builder must report under RIDDOR.

NoteHealth surveillance finds damage that has already started. HSE is clear that it is never a substitute for controlling the dust.

How do you do a COSHH assessment for a task?

  1. 01Name the task and the materials. Chasing a blockwork wall for cables, cutting paving, sanding plaster: one task, one site, one set of materials.
  2. 02Identify the substances. Read the label and the safety data sheet for every product, then add what the work itself creates. HSE’s examples are wood dust from sanding and silica dust from tile cutting, and process dust has no data sheet of its own.
  3. 03Look up the limits. Check each substance against EH40 and note any carcinogen or sensitiser notation.
  4. 04Decide who is exposed and how. The operatives, anyone nearby, how long and how often, and by which route: breathing, skin or swallowing.
  5. 05Remove what you can. Change the design, the method or the material before choosing a control.
  6. 06Choose controls for what remains. Water or on-tool extraction first, then RPE of the right APF, then screening, cleaning and welfare.
  7. 07Write it down and brief it. The findings and the controls go into the RAMS for the task, and the operatives are briefed before they start. A signed toolbox talk is the usual evidence.
  8. 08Review it when the work changes, when monitoring or health surveillance says so, or when the dust is plainly escaping.
StepEntry
TaskChasing a blockwork wall for cable runs in an occupied house: two operatives, about three hours
SubstanceRespirable crystalline silica from the blocks and mortar. WEL 0.1 mg/m³; carcinogen notation
Who is exposedThe two operatives, the householder and any other trade in the house
RemovedSurface trunking in the utility room, agreed with the electrician, removes two chases
At sourceWall chaser with on-tool extraction to an M class unit; flow indicator checked before starting
RPEFFP3 masks (APF 20), each wearer fit tested on that model and clean-shaven
OtherDoor shut and sheeted, room cleared, vacuum not brush, waste bagged and sealed
ChecksExtractor’s last thorough examination within 14 months; filter changed
BriefingToolbox talk on the morning, signed by both operatives

Illustrative assessment for a worked example. Your task, materials and controls will differ.

Free toolRAMS templateHas a section for the substances and where the data sheets are held, beside the method, the PPE and the briefing record.

Which other substances should a builder assess?

SubstanceHazard HSE namesTypical control HSE gives
Hardwood dustListed as a carcinogen in COSHH (HSE links wood dust to nasal cancer); asthmaPre-cut materials, on-tool extraction to H or M class, RPE of APF 20
Softwood dustRespiratory sensitiser (asthma)As for hardwood dust
Plasterboard and gypsum dustGeneral dust with little or no silicaOn-tool extraction to H, M or L class
Wet cement, concrete and mortarIrritant and allergic dermatitis; burns that can need skin graftsWaterproof gloves suitable for alkalis, long enough to stop cement getting in; prompt washing; skin checks
Cement powderRespiratory irritantPre-mixed concrete or mortar to avoid handling powder

Hazards and controls as HSE states them in its construction dust and cement guidance.

Anything else bought in a tin or a tube, from resins to solvents, gets its hazards and controls from the safety data sheet, which COSHH makes part of the assessment and which every exposed worker must be able to see.

What does Estimark record?

A COSHH entry in Estimark holds the substance, its CAS number, the hazard classification, a risk rating, the control measures, the PPE, a link to the safety data sheet and a review date, and can sit on the job it belongs to. It lives in health and safety beside the job’s versioned RAMS, each signed by the operatives against the version they were briefed on, and the toolbox talk registers.

Face fit is one of the named qualification types in training and qualifications, held per worker with the date, the expiry and the certificate, with an alert before it lapses. Estimark does not run health surveillance, measure exposure or decide whether your controls are adequate. The assessment is yours; the record of it is in one place.

Sources

Questions

Frequently asked

What is the exposure limit for silica dust?

The workplace exposure limit for respirable crystalline silica in Great Britain is 0.1 mg/m³ as an 8-hour time-weighted average, from HSE’s EH40/2005. EH40 marks it as a carcinogen where it is generated by a work process, so exposure must also be kept as low as is reasonably practicable.

Do I need a written COSHH assessment?

You need an assessment whatever your size. Regulation 6(4) of COSHH requires the significant findings to be recorded where you employ five or more people. HSE says it makes sense to write it down even with fewer, and a principal contractor will usually ask to see it in your RAMS.

What class of dust extractor do I need for cutting concrete?

HSE’s construction dust guidance says to use an H (high) or M (medium) class extraction unit for silica dust, not a general commercial vacuum. An L (low) class unit is suitable only for lower-toxicity dust such as gypsum from plasterboard.

How often does on-tool extraction need testing?

At least every 14 months. Regulation 9 of COSHH requires a thorough examination and test of local exhaust ventilation at that interval, and HSE confirms it applies to on-tool extraction. Records are kept for at least five years.

Can someone with a beard wear a dust mask?

Not a tight-fitting one. HSE says wearers of tight-fitting masks must be clean-shaven where the mask seals, because stubble or a beard breaks the seal. A loose-fitting powered hood or helmet does not rely on a face seal and needs no fit test.

Does COSHH cover asbestos?

No. Asbestos is covered by the Control of Asbestos Regulations 2012 and lead by the Control of Lead at Work Regulations 2002. Regulation 5 of COSHH excludes both from its assessment and control duties.

Build on a solid foundation.

Run the whole business without an implementation project and without legacy baggage. Every plan starts with 14 days free. No card needed.

Estimating · Jobs · Invoicing · CIS · H&S · Reactive maintenance