Health & Safety
Work at height: the rules builders actually have to follow
The short answer
The Work at Height Regulations 2005 apply to any work where, without precautions, a person could fall a distance liable to cause personal injury. There is no minimum height: HSE’s examples include falling from ground level into a hole. Every job at height must be properly planned, including for rescue, appropriately supervised and done by competent people. Regulation 6 sets the order: avoid work at height where you reasonably can, prevent a fall with a safe existing place or with equipment such as a scaffold, tower or mobile elevating work platform, and only then minimise the distance and consequences of a fall. Guard-rails and other collective protection come before harnesses. Ladders are allowed for low-risk, short-duration work; HSE’s guide is no more than 30 minutes at a time. The regulations cover Great Britain; Northern Ireland has its own.
At a glance
- Regulations
- Work at Height Regulations 2005, S.I. 2005/735
- Minimum height
- None: a fall liable to cause injury (reg 2)
- Order of precautions
- Avoid, prevent, mitigate (reg 6)
- Top guard-rail, construction
- At least 950 mm (Schedule 2)
- Gap between rails
- No more than 470 mm (Schedule 2)
- Ladder guide (HSE)
- No more than 30 minutes at a time
- Platform inspection
- Within 7 days if a fall of 2 m or more (reg 12(4))
- Northern Ireland
- Work at Height Regulations (NI) 2005
What counts as work at height?
Regulation 2 defines work at height as work in any place, including a place at or below ground level, where a person could fall a distance liable to cause personal injury if the precautions the regulations require were not taken. Getting to and from that place counts too, except by a staircase in a permanent workplace.
- Working on a ladder, a stepladder, a scaffold or a flat roof.
- Working where you could fall from an edge, through an opening or through a fragile surface.
- Working at ground level beside an opening in a floor or a hole in the ground you could fall into.
HSE adds two exclusions: a slip or trip on the level is not a fall from height, and nor is walking up and down a permanent staircase in a building.
The Work at Height Regulations 2005 set no minimum height. If a fall could injure someone, they apply, whether the edge is a hop-up or a roof.
HSE calls work at height the biggest single cause of fatal and serious injury in construction, particularly on smaller projects. The duties fall on employers, on anyone controlling work at height by others, and on the self-employed working on a construction site.
NoteThe 2005 regulations apply in England, Scotland and Wales. Northern Ireland has its own Work at Height Regulations (Northern Ireland) 2005, so check those if you work there.
What must be in place before anyone goes up?
Regulation 4 requires work at height to be properly planned, appropriately supervised and carried out in a manner that is, so far as reasonably practicable, safe. The planning includes choosing the equipment under regulation 7 and planning for emergencies and rescue.
- Planning in proportion. HSE says low-risk, straightforward tasks need less planning effort.
- A rescue plan. How does somebody hanging in a harness or stuck on a platform get down? HSE says not to rely on the fire brigade, because the delay may be critical.
- The weather. Work at height goes ahead only when the weather does not put people at risk. For roof work HSE says not to go on a roof in rain, ice, frost or strong winds, and that winds above 23 mph (Force 5) will affect a person’s balance.
Who counts as competent?
Regulation 5 says nobody may take part in any activity in relation to work at height, including organising, planning and supervising it, unless they are competent or are being trained under the supervision of a competent person. HSE describes competence as the skills, knowledge and experience to do the task.
- For low-risk, short-duration ladder work, HSE says competence may mean no more than instruction, such as how to tie a ladder, often given on the job. No formal qualification is needed.
- For technical work, such as planning a complex scaffold, HSE points to industry training and certification schemes. For mobile towers it names PASMA or a recognised manufacturer or supplier scheme.
What is the work at height hierarchy?
Regulation 6 sets the order, taking account of the risk assessment you make under regulation 3 of the Management of Health and Safety at Work Regulations 1999.
- 01Avoid. Do not work at height where the job can reasonably be done safely another way, such as with extendable tools from the ground.
- 02Prevent. Where it cannot be avoided, work from an existing place that is already safe, such as a flat roof with permanent edge protection, or provide equipment that stops a fall: a scaffold, a tower, or a mobile elevating work platform (MEWP) such as a scissor lift.
- 03Mitigate. Where a risk of falling remains, minimise the distance and consequences of a fall with nets or soft landing systems close under the work, or a fall arrest system with a high anchor, plus training and instruction.
Regulation 7 adds that collective protection takes priority over personal protection. HSE defines collective protection as equipment that works without the person having to do anything, such as guard-rails, scissor lifts and tower scaffolds. Personal protection needs the person to act, such as putting on a harness and clipping its lanyard to an anchor.
The choice also has to account for the conditions, the distance and consequences of a fall, how long the equipment is used, and how quickly someone could be rescued from it.
HSE says the hierarchy must be followed in order. Reaching for a harness and lanyard in the first instance, before considering a scaffold or a tower, is not acceptable.
How do you plan a job at height?
- 01Describe the task. Where, how high, how long, how often, and what the surface is like.
- 02Ask whether it can be done from the ground. Extendable tools, or assembly at ground level.
- 03If not, prevent the fall. An existing safe place first, then a scaffold, tower or MEWP.
- 04Only then consider personal protection. Work restraint, which stops someone reaching an edge, before fall arrest, which catches them after.
- 05Look for fragile surfaces and falling objects. Roof lights, cement sheets, people below, and where materials will sit.
- 06Name the competent people. Who erects, who inspects, who uses, and who supervises anyone in training.
- 07Plan the rescue. Who brings a person down, with what, and how fast.
- 08Check the weather on the day.
- 09Inspect before use. The equipment after assembly, and the place of work before each use.
- 10Write it into the RAMS and brief it. See what a RAMS must contain.
Which equipment suits which job?
HSE does not publish one master table, but its guidance says what it expects for the jobs builders most often do. Each row below is HSE’s own position.
| Task | What HSE says | HSE source |
|---|---|---|
| Re-roofing or repairs on a house | Almost all domestic roof work needs scaffolding with edge protection at eaves and gable ends, and around chimneys and roof windows | CIS60 Roof repair work |
| Replacing a few broken tiles or adjusting an aerial | Short-duration work; a roof ladder can be used where more suitable equipment cannot, anchored on the opposite slope, not on the ridge capping | Construction work at height FAQs |
| Work on or near a fragile roof or roof light | Work from underneath, or from a MEWP basket; if the roof cannot be avoided, edge protection, staging, and nets or a harness | GEIS5 Fragile roofs |
| Brief light work such as hanging wallpaper or fitting a ceiling smoke detector | A stepladder can be justified, keeping three points of contact: two feet and a hand, or two feet and the body supported by the steps | Common work at height myths |
| A task needing more than 30 minutes at a time up a ladder | Use alternative equipment | Safe use of ladders and stepladders |
| Work that cannot be done from the ground or an existing safe place | Prevent a fall with collective protection: a MEWP such as a scissor lift, a tower scaffold or a scaffold | Step-by-step guide |
| Plastering or painting at ceiling height | Stilts are acceptable if the user is trained and competent and the floor is even, dry and free of trailing cables | Construction work at height FAQs |
| Climbing between levels | An industrial ladder, tied and extending at least 1 metre above the landing; stepladders are not for access unless designed for it | Securing ladders; myths |
HSE’s published statements, summarised. Your risk assessment decides the job in front of you.
Guard-rails, platforms and towers
Schedule 2 sets the guard-rail figures for construction work: the top guard-rail at least 950 millimetres above the edge a person could fall from (910 millimetres for rails already fixed when the regulations came in), and no gap of more than 470 millimetres between an intermediate rail and other protection. Toe-boards must be suitable and sufficient to stop people or materials falling; HSE says one at least 100 millimetres high would be acceptable. A rail can come off only for the time and extent needed for access or a particular task, and goes back as soon as practicable.
For a mobile tower, HSE expects guard-rails all round every platform at 950 millimetres with no more than a 470 millimetre gap, a built-in ladder or stair, four stabilisers, toe-boards, and a build method that keeps the erector protected: advance guard-rail or through the trap.
When can you use a ladder or stepladder?
Ladders are not banned. Schedule 6 allows a ladder for work at height only where a risk assessment shows that more suitable equipment is not justified because the risk is low and either the use is short or there are existing features on site you cannot alter.
HSE’s guide: if the task would keep someone up a leaning ladder or stepladder for more than 30 minutes at a time, use other equipment. Short duration alone does not make a ladder acceptable; the risk comes first.
Leaning ladders
- Set it at the 1 in 4 angle: one unit out for every four up, about 75 degrees.
- Secure it: tie both stiles; if that is not practical, use an effective stability device; if not, wedge it; footing is the last resort.
- Do not work off the top three rungs, and have the ladder extend at least 1 metre or three rungs above where you are working.
- Keep your belt buckle within the stiles and three points of contact, other than for a moment such as starting a screw.
- Do not rest it on glazing or plastic gutters, or work within 6 metres horizontally of an overhead power line unless it is dead or insulated. Use a non-conductive ladder for electrical work.
Stepladders
- All four feet on the ground, the steps level and the locks engaged.
- Do not stand and work on the top three steps unless there is a suitable handhold.
- Face the work where you can, and avoid side loading such as side-on drilling into brick or concrete. Where it cannot be avoided, tie the steps or use other equipment.
Checks
The user checks stiles, feet, rungs and locks at the start of the day and after anything changes, with no record needed. Detailed visual inspections are the employer’s, done by a competent person at fixed intervals and recorded. A ladder rising 9 metres or more needs landing areas or rest platforms where reasonably practicable.
How do you deal with fragile roofs and falling objects?
A fragile surface is one that would be liable to fail under any reasonably foreseeable loading. HSE’s list of likely fragile materials: roof lights, liner panels on built-up sheeted roofs, non-reinforced fibre cement sheets, corroded metal sheets, glass including wired glass, rotted chipboard, slates and tiles.
Regulation 9 works in the same order as the hierarchy. Nobody passes across or near, or works on or from, a fragile surface where the job can reasonably be done without it. Where it cannot, provide platforms, coverings or guard-rails that carry the load, and take steps to minimise the distance and consequences of any fall that still could happen. Put prominent warning notices at the approach to the fragile area, or make people aware of it some other way.
Falling objects and danger areas
Regulation 10 requires you to prevent materials and objects falling where that could injure someone, and where you cannot, to stop anyone being struck. Nothing is thrown or tipped from height where it could hurt somebody, and materials are stored so they cannot collapse or slide. Regulation 11 adds that an area where people could fall or be struck is fenced off from unauthorised entry and clearly marked.
HSE turns that into site practice: no ‘bombing’ from the roof or scaffold, so use a chute; debris netting or mesh to stop materials falling; and an exclusion zone below the work.
NoteA fall through a roof light or a dropped load that hits a passer-by can be reportable to HSE. See what a builder must report under RIDDOR.
Who inspects the equipment, and how often?
Regulation 12 covers guard-rails, working platforms, nets, personal fall protection and ladders.
- After assembly. Where the equipment’s safety depends on how it was put up, it is inspected in that position before use.
- When conditions could cause deterioration. At suitable intervals, and after anything exceptional such as high winds or accidental damage.
- Construction working platforms. Where a person could fall 2 metres or more, the platform is not used unless inspected within the previous 7 days, with a written report. A mobile tower is inspected on the site rather than each time it moves. The full rules are in scaffold inspections: the seven-day rule.
- Hired or borrowed kit. It must come with physical evidence that its last inspection was done.
- The record. The result of each inspection is recorded and kept until the next one.
Regulation 13 adds a check of the place of work itself, its surface and any parapet or rail, before each use. For harnesses, HSE recommends a pre-use check each shift and a recorded detailed inspection at least every six months.
How does Estimark help with work at height?
Estimark issues permits to work, and working at height is one of the permit types, alongside hot work and confined space. Each permit carries a number, a location, a risk level, the precautions and PPE, validity dates, an approval and a status from draft to active to closed, and prints as a PDF. The same permits cover hot works. The job’s RAMS is versioned, and each operative signs the version they were briefed on.
Training and qualifications holds IPAF, PASMA and working at height as named qualification types for each worker, with the card number, the expiry date and an alert before it lapses. Estimark does not choose your access equipment, inspect a scaffold or decide whether a ladder is justified. See health and safety in Estimark and training and qualifications.
Sources
- Work at Height Regulations 2005 (legislation.gov.uk)
- Work at Height Regulations (Northern Ireland) 2005 (legislation.gov.uk)
- Work at height: frequently asked questions (HSE)
- Common work at height myths (HSE)
- How and when to use a ladder at work (HSE)
- Types of ladder and using them safely (HSE)
- Securing ladders and ladders used for access (HSE)
- Working at height: a brief guide, INDG401 (HSE)
- Construction: work at height FAQs (HSE)
- Assessing all work at height (HSE)
- Fragile roofs: safe working practices, GEIS5 (HSE)
- Roof repair work: what you need to know as a busy builder (HSE)
Questions
Frequently asked
Is there a minimum height for work at height?
No. The Work at Height Regulations 2005 apply wherever a person could fall a distance liable to cause personal injury, including into a hole at ground level. A 2 metre figure appears only in specific rules, such as the 7-day inspection of construction working platforms from which a person could fall 2 metres or more.
Are ladders banned on building sites?
No. Schedule 6 allows a ladder where a risk assessment shows more suitable equipment is not justified because the risk is low and the use is short, or because of features on site you cannot change. Ladders can also be used to reach a scaffold if they are industrial grade, tied and extend at least 1 metre above the landing.
How long can you work from a ladder?
HSE’s guide is no more than 30 minutes at a time on a leaning ladder or stepladder; beyond that, use other equipment. HSE also describes short-duration work as tasks measured in minutes rather than hours, and says the risk must be considered first, whatever the duration.
Do you need a qualification to use a ladder at work?
No. HSE says you need to be competent, meaning the skills, knowledge and experience to use the ladder properly for the job, or to be supervised by somebody competent while you are trained. Training often happens on the job.
How high must guard-rails be on a scaffold?
For construction work, Schedule 2 requires the top guard-rail to be at least 950 millimetres above the edge, with no gap of more than 470 millimetres between rails. Toe-boards must be suitable and sufficient; HSE says a toe-board at least 100 millimetres high would be acceptable.
Read next
Scaffold inspections: the seven-day rule
Before first use, every seven days, after anything that affects stability, and what the report must say.
What must a RAMS actually contain?
The legal duty behind it, the sections a good one has, and what gets them rejected.
What must a builder report under RIDDOR?
Deaths, specified injuries, over-seven-day injuries and dangerous occurrences: who reports, how and by when.
Estimark: health and safety
Versioned RAMS signed per operative, inductions that expire, toolbox talks, near misses and permits to work.
RAMS template
Risk assessment, method statement, emergency arrangements and a signed briefing record.
Run the paperwork once.
Estimating, jobs, invoicing, CIS and compliance in one place. 14 days, full access, no implementation fee and no card needed.